Mine Crusher Dust CollectorDuring Installation, Sealed Devices Or Dust Collection Covers Should Be Installed At The Feeding And Discharging Ports, Upper Parts Of Vibrating Screens, And Belt Conveyor Transfer Points Of Crushers Or Crushers For Raw Materials Such As Ore, Lump Ore, Limestone, Dolomite, Bauxite, And Coal. Double Layer Sealed Covers Should Be Installed At The Receiving Points Of The Transfer Points. Cover The Dust Producing Equipment With A Closed Hood, Or Create A Dust Collection Chamber To Create A Uniform Negative Pressure Inside The Hood To Prevent Dust From Escaping, Or Use An Open Suction Hood To Create A Suction And Capture Airflow, Controlling The Exposed Dust Area Within A Narrow Range, So That The Dust Carrying Airflow Is Sucked Away, Purified By A Mining Bag Filter, And Discharged Through A 15 Meter Chimney.
Working Principle Of Dust Collector For Mine Crusher:
The Dusty Gas Enters The Volute Type Cyclone Tube Through The Air Duct, And The Dust Runs Along The Inner Wall Of The Dust Removal Equipment Shell Under The Action Of Centrifugal Force. The Coarse Dust Is Separated And Enters The Ash Hopper. The Fine Dust Passes Through The Dust Removal Filter Bag With The Gas To Become Clean Gas, Which Is Discharged Into The Atmosphere By The Fan. The Fine Powder Is Blocked By The Dust Removal Filter Bag On The Outer Surface And Falls Into A Dust Cake, Achieving The Purpose Of Dust Removal And Purification.
The Dust Collector Of The Mine Crusher Is Suitable For Coarse And Intermediate Crushing Of Brittle Block Materials In Industries Such As Cement, Chemical, Power, Mining, Metallurgy, Building Materials, Refractory Materials, And Coal Mines. It Has A Large Feed Particle Size And Adjustable Discharge Particle Size, And Can Crush Materials With Compressive Strength ≤ 160MPa. Especially In The Coal Industry, When Using This Machine To Crush Raw Coal, It Can Be Directly Crushed As Long As It Undergoes Iron And Impurity Removal Without The Need For Gangue Removal. The Crushed Material Has Uniform Particle Size And Low Over Crushing Rate, Simplifying The Coal Preparation Process And Reducing Investment And Production Costs. The Commonly Used Mining Crushing Equipment Currently Includes: E-type Crusher, Impact Crusher, Air Selection Crusher, Hammer Crusher, Impact Crusher, Roller Crusher, Composite Crusher, Cone Crusher, Etc.
Components Of Dust Collector For Mine Crusher:
The Structure Of The Dust Collector For The Mine Crusher Consists Of A Dust Collector Cover, A Rotating Cover Removal Device, A Cleaning Room, A Bag Changing Inlet, An Observation Hole, And An Air Outlet. Flower Board, Filter Bag, Filter Bag Frame, Filter Bag Guide, Filter Chamber Cylinder, Air Inlet, And Inlet Door. Including Positioning Support Frame, Ash Hopper, Star Shaped Ash Discharge Valve, And Support. It Is Composed Of A Rotating Arm, A Nozzle, A Loop Back Blowing Mechanism, A Circulating Air Duct, A Back Blowing Duct, A Back Blowing Machine, And A Rotating Arm Deceleration Mechanism.
Characteristics Of Dust Collector Equipment For Mine Crushers:
1. Good Dust Removal Efficiency, With A Dust Concentration Of Less Than 10mg/Nm3 In The Outlet Gas, Especially For Fine Dust With High Dust Removal Efficiency.
2. The Structure Of The Dust Removal Equipment For Mine Crushers Is Very Simple, And The Operation And Maintenance Are Relatively Convenient, Reducing The Workload Of Maintenance.
3. The Control System Adopts A Pulse Control System To Regularly Spray And Clean The Equipment, With Good Spraying Effect.
4. The Dust Removal Filter Bag Is Made Of Needle Punched Felt Filter Material And Carbon Steel Expansion Ring, Which Not Only Has Good Filtering Effect, But Also This Expansion Ring Design Is Very Easy To Disassemble And Firm, And There Will Be No Bag Falling Phenomenon.
5. Adopting A Vacuum Hood Design, It Can Collect And Filter Dust From Dust Sources.
6. Mining Dust Collectors Can Be Designed With Multi-point And Single Point Suction According To User Needs.
The Dust Collector Of The Mine Crusher Can Be Combined With Multiple Dividers Of Different Specifications According To Different Specifications Of Solenoid Valves. This Series Of Dust Collectors Can Operate Under Negative Or Positive Pressure, And Its Body Structure Remains Unchanged. The Dust Collection Efficiency Is Over 90%, And The Dust Concentration Of The Purified Gas Is Less Than 100mg/m ³. If This Series Of Dust Collectors Is Used In Cold Areas Or When The Flue Gas Is Below Zero, Insulation And Heating Devices Need To Be Added, And The Shell Should Also Be Changed Accordingly.
